• Summary
  • Features
  • Specs
  • Accessories
  • Parts
  • Brochure
  • Quote
5-Axis Vertical Machining Center

The Sharp SVX- 300 vertical machining center is engineered to have unrivaled quality and outperform all other machines in its category. Sharp’s SVX-300 allows true 5-sided and 5-axis simultaneous machining. 

Unlike the 3-axis that requires a separate setup for cutting different sides of a part, the 5-axis machine requires the part to be set only once and rotated into a series of positions to machine each side without the need to reset the part. 

All major castings of the SVX-300 are analyzed using the Finite Element Method (FEM) to locate areas of stress and strain, multiple loading conditions from thermal, gravity, centrifugal and enforced displacement.

Extensive Ribs design are properly defined to maintain rigidity throughout the entire machine. The Cross Roller Linear Guideways are equipped with 6 supporting blocks to ensure accurate linear movements.


  • 30" x 23.6" x 19.7" travel (X,Y,Z)
  • 11.8" Trunnion table with A and C axis travel.
  • 12,000 rpm, CAT 40, 15 HP
  • Fanuc 31i-B5 control, also available Heindenhain or Siemens control. 
SHARP SVX-300    
Fanuc   31i-B5
Screen Size   10.4"
*Siemens, Heidenhain control are also available
X axis travel inch (mm) 30" (760)
Y axis travel inch (mm) 23.6" (600)
Z axis travel inch (mm) 19.7" (500)
A axis travel Degree -120 ~ 30°
C axis travel Degree 360°
Spindle nose to table (A=0°) inch (mm) 3.9"-23.6" (100-600)
Table area inch (mm) 11.8" (300)
Max workpiece wt. lb (kg) 330  (150)
T-Slot (Width x Degree)   0.7"x 45° (18 x 45°)
Speed rpm 12,000
Taper   CAT40
Bearing   Ceramic bearing
Type   Direct Drive
Spindle oil chiller   Oil Type
Feed Rate    
Rapid traverse X/Y Axis ipm (mm/min) 1,417 (36,000)
Rapid traverse Z Axis ipm (mm/min) 1,417 (36,000)
Cutting feed rate ipm (mm/min) 0.04-393 (1-10,000)
Transmission   Direct Drive
Spindle motor Hp (Kw) 10/55 (7.5/11)
Automatic Tool Changer    
ATC capacity   24
Method of tool selection   Set tool number
ATC type   Arm type, CAT40
Max tool diameter inch (mm) 2.9" (75)
Max. tool length inch (mm) 11.8" (300)
Max. Tool weight lb (kg) 15.4 (7)
Without adjacent tool inch (mm) 5.9" (150)
Air blast at tool change   OK
X, Y, Z axis: Position inch (mm) +/-0.0002" (0.0015")
X, Y, Z axis:Repeatability inch (mm) +/-0.00012" (0.0015")
A axis: Position arc seconds +-15
A axis: Repeatability arc seconds +-6
C axis: Position arc seconds +-15
C axis: Repeatability arc seconds +-6
Machine measurements    
Floor space inch (mm) W: 91.3"(2320) x D:119" (3,000)
Height inch (mm) 124.1" (2,960)
Weight lb (kg) 28,050 (12,750)
Door opening inch (mm) 43.3" (1,10)
Coolant system    
Flood coolant nozzles   6
Coolant tank capacity gal (L) 53 (240)
Chip Conveyor   Hinge type
Air blower nozzle (for cutting dry)   1
Power requirement    
Electrical 220V/60 Hz 3 Phase/45 KVA
Air   6 CFM @ 88psi

Standard Accessories 

  • Fanuc 31i-B5 control, 10.4" color LCD
  • Tool setter
  • Work piece probe
  • Spindle air blast (Auto)
  • Electric cabinet heat exchanger
  • Spindle oil chiller
  • Oil skimmer
  • Hinge type chip conveyor with bucket
  • Fully enclosed splash guard
  • Coolant system-240L tank capacity
  • CTS preparation (70 Bar)
  • Coolant Gun, air
  • AICC II (200 block look ahead)
  • Manual guide I
  • USB port
  • Embedded Ethernet
  • RS-232C Interface
  • 2 MB memory
  • 3 Dimensional cutter
  • 3D interference check
  • High-speed smooth TCP
  • Rigid tapping

Please contact our parts department at 310-370-5990.

There are no brochures for this product at this time.

Get a Quote

Get Your Free Quote Below!

Need to request a part? Go to our Parts Form

*Prices may vary based on location